Unmatched Flexibility With The Industry's Most Uniform Performance

Sunflower introduced the first Flexible Offset Disc to the American farmer in 1968. With over 30 years of Disc building experience, Sunflower knows what it takes to make them work. Even today, the 1300 Series Disc from Sunflower is the best flexible Offset disc on the market. Capable of performing primary through finish discing operations and loaded with performance enhancing features, you will see how the 1300 series can increase your efficiency with each tillage pass.

Staggered Overlapping Disc Gangs

 

With the exception of the 1300 , 1700 and 1800 series, every Sunflower disc features staggered overlapping disc gangs - one of the keys to level discing. The overlapped placement of the front gangs cuts all of the ground cleanly while the staggered rear gangs throw the soil back in a criss-cross pattern. This arrangement eliminates the need for a chisel shank or bulk buster typically required in the center and behind the front gangs of conventional tandems. Even more importantly - the Sunflower combination eliminates ridging in the center - another problem common with conventional tandem discs. Sunflower also makes sure the tires are placed close to the hinge line on the center section and the outside of each wing. This assures the disc will perform properly, without gouging, in rough or terraced ground. Some manufactures save money by simply extending the gang bars on the wings to make the next large size. This leaves the wing wheels too far inside and they cannot control the wings in rough or terraced ground.

 

Featured on all except: 1300, 1700 & 1800 series disc

Trunnion Mounted Bearings

Sunflower's trunnion bearings provide positive alignment, eliminate wear between the bearings and the housing and ensure positive lubrication. As the C-Flex™ bearing standards move, the gang bearings have to constantly realign. On conventional bearing systems the bearing moves within the housing. This eventually leads to wear between the bearing and the housing... then bearing failure, because grease cannot get into the bearing. With the trunnion bearing there is never any wear between the bearing and the housing and there is always positive lubrication. The trunnion bearing features triple lip seals that cannot be damaged by daily greasing and metal washers that protect the seals from being damaged by stocks or material wrapping around the gang shaft.

 

Featured on all except: 1700 & 1800 series disc

C-Flex™ Bearing Standards

 

 

Standard equipment on every Sunflower disc, the C-Flex™ bearing standards absorb disc gang shock created by stumps, rocks and normal discing. This extends the bearing, spool and disc blade life. A bonus feature is the C-Flex's™ ability to clear residue better than conventional rigid standards. The C-Flex™ bearing standards also allow for easy maintenance of the disc gang assembly. Just remove one bolt and loosen another bolt at each C-Flex™ location and the entire gang can be dropped. All C-Flex™ standards remain in place to assure the gang will be in the correct position when replaced. Unlike competitive machines the scraper bars are mounted to the back of the C-Flex™ Standards. This allows the scrapers to react with the gang and not come into contact with the spools or blades.

 

Featured on all except: 1700 & 1800 series disc

Spring Cushion Gang Assembly

 

 

The entire gang assembly pivots upwards when an obstruction is encountered. The heavy coil springs compress allowing the gang assembly to pass over the obstruction then expands to return the gangs to their working position. 

 

Optional on 1700 & 1800 series 

Rigid Gang Assembly

 

 

Standard equipment on 1700 & 1800 series 

Self-leveling Hitch

Front-mounted Gauge Wheels

A trademark on all flexible Sunflower discs is front-mounted gauge wheels. This important feature prevents the front gangs of the wing frame from gouging, buckling or cutting deeper than the other gangs, promoting a level, ridge or furrow free field. The heavy-duty gauge wheels feature a 5-bolt hub and 8.00 x 10 ply tire.

 

Featured on all winged units except 1700 & 1800 series

Variety of Disc Blade Diameters

 

Sunflower offers a variety of disc blade diameters, thickness and spacing to allow you to select the best combination for your farming operation. All spools, whether precision machined cast iron or precisely fabricated steel, provide a perfect fit between it and the disc blade, resulting in smooth free turning gangs. High strength 1 3/4" to 2 1/2” diameter round stress proof gang shafts and factory assembled gangs are torqued hydraulically to approximately 1,500 pounds. Spring end collars (all except 1700 & 1800 series) on each end of the gang are collapsed slightly and make sure the gang stays tight. This results in thousands of trouble free acres.

 

Notched blades available on 1700 & 1800 series

Maintenance-free Lift Systems

Sunflower discs are equipped with maintenance-free lift systems. These systems pivot on space-age UHMW polymer sleeves eliminating greasing.

 

Maintenance Free Wing Hinges

 

Maintenance free wing hinges that utilize the same UHMW technology as the lift systems are used on some models.

 

Featured on all except 1300, 1700 & 1800 series 

 

Wheel Assemblies - Walking Tandems

The walking beam pivot assemblies are comprised of two tapered roller bearings with triple-lipped seals.

Wheel Assemblies - Dual Wheels

 

For ease of service and strength, the wheel spindles of all configurations, dual, tandem or triples, slip into the spindle tube which is welded into the walking beam.

Wheel Assemblies - Walking Triple Tandems (1550 Series)

 

Center section walking triple tandems have 50% more weight carrying capacity than conventional walking tandems. 

Three Row H.D. Coil Tine Harrow

 

The H.D. harrow has 1/2” x 22” (12.7 x 559 mm) heavy duty tines on 12” (305 mm) centers, creating a 4” (102 mm) overall tine spacing. The configuration has 12” (305 mm) spacing between rows for better residue flow. Adjustable spring loaded mounting arms provide the necessary down pressure.

 

Available for: 1435, 1444, 1544, 1550, series 

Three Row H.D. Coil Tine Harrow

 

The H.D. harrow has 5/8” x 26” (16 x 650 mm) heavy duty tines on 12” (305 mm) centers, creating a 4” (102 mm) overall tine spacing. The configuration has 12” (305 mm) spacing between rows for better residue flow. Adjustable spring loaded mounting arms provide the necessary down pressure.

 

Available for: 1700 & 1800 series 

2-Bar H.D. Coil Tine Harrow & Reel

 

The two bar coil tine combined with a flat bar rolling basket. The harrow is designed with 12” (305 mm) between tooth bars and has five tine adjustment for tooth angle. The double tine tooth is 5/8” x 26" (15 x 650 mm) and the reel is 13” (330 mm) diameter with eight, 1/4” x 1-1/4" (6.3 x 31.75 mm) wide steel blades. 

 

Available for: 1700/1800 series

Three Row Coil Tine Harrow

 

Features three rows of 3/8" x 16" coil tines on 2 1/2" centers spaced 15" between bars. Each tine is individually mounted for easy replacement - no need to disassemble a complete bar. Each section features backup protection and can be adjusted for tine pitch, height, tilt and down pressure. 

Available for all Models except 1700 & 1800 series

 

Three Row Spike Drag Harrow

 

Available for 1435 & 1544 

Rear Tow Hitch

Several rear tow hitch options are available. The model shown in the photo features a slide hitch and ball joint for ease of hook-ups in limited space situations.

 

Trail hitches are available for all models except 1444 & 1544 series